Descrizione del prodotto
Coresun Drive slewing drive gear motor worm drive for horizontal single-axis solar tracking system. For horizontal single-axis solar tracking system, the main shaft of solar panel will adjust the angle to precisely track the declination angle. This kind of slewing drive is only applied for low latitudes area.
Slew Drive is a new type of slewing product, usually called slewing ring, which is usually composed of worm, slewing ring, housing, motor and other components. Since the core components are slewing bearings, they can simultaneously withstand axial forces, radial forces, and overturning moments. Compared with traditional rotary products, the new slewing drive features easy installation, easy maintenance and a greater degree of installation space.
Slew Drive are widely used in PV,CPV,STP solar tracking systems and construction applications including truck cranes, manlifts, turntables, port machinery, modular vehicles, small wind power systems and satellite communications.
Glossary
Tilting Moment Torque: Torque is the load multiplied by distance between the position of load and the center of slewing bearing. If the qorque generated by load and distance is greater than the rated tilting moment torque, slewing drive will be overturned.
Radial load: Load vertical to the axis of slewing bearing
Axial load: Load parallel to the axis of slewing bearing
Holding torque:It is the reverse torque.When the drive is rotating reversely, and parts are not damaged,The maximum torque achieved is called holding torque.
Self-locking: Only when loaded, the slewing drive is not able to reverse rotate and thus called self-loc
| Model | VH9 | Place of Origin | HangZhou,China |
| Brand | Coresun Drive | Type | Vertical |
| Materiale | 42CrMo,50Mn | Coppia in uscita | 6405N.m |
| Tilting Moment Torque | 12KN.m | Holding Torque | 56KN.m |
| Static Axial Rating | 350KN | Static Radial Rating | 120KN |
| Dynamic Axial Rating | 168KN | Dynamic Radial Rating | 65KN |
| Gear Ratio | 61:1 | Efficienza | 40% |
Chi siamo
CHINAMFG – Practical Slewing Drive & Slewing Bearing Promoter.
We are committed to researching, developing and applying high quality, precision transmission equipment products,who provides reliable mechanical actuator for horizonal single axis, dual-axis photovoltaic tracking system, CSP,CPV solar tracking design.Our professional and high-quality products will be also applied well as a steady solution on aerial working platform, truck crane, timber grab, drilling rig, spray equipment, hydraulic module vehicle,automated assembly lines, wind yaw systems,etc.
1. Our company’s worm gear reducer (slewing drive device) adopts the transmission mode of plane secondary enveloping ring surface worm combined with slewing support, which can realize multi-tooth meshing.
2. On the premise of not affecting the performance of the whole device, we improved and optimized it, and its overall thickness became thinner and weight became lighter.
3. The rotary device at the center is a through hole for the customer to use. The original product is solid.
4. The worm material is 42CrMo, the secondary nitride treatment, the slewing bearing material is 50Mn, the teeth are quenched, and its wear resistance is good.
Why choose us
1. We are a manufacturer of producing slewing drive and bearing for more than 10 years.
2. We have advanced mechanical equipment and strict quality control team.
3. Efficient production speed and on-time delivery service.
4. Accept standard and non-standard production.
Products Photo
Application
Photovoltaic power generation is an important application field of rotary drive, using slewing drive VH9 as a rotating component of solar photovoltaic modules, according to the position of the sun in a day to the host of the angle and elevation of accurate adjustment, time is the solar panel for better reception angle, can make greater efficiency of power generation.
Horizontal Single Axis PV solar tracker system. The slewing drive VH9 is available for 60-150 square meter solar tracker design.
Products Certificate
Coresun Drive slewing drive gear motor have arroved by CE and ISO2001 certificate.
CONTACT US
It is sincerely looking CHINAMFG to cooperating with you for and providing you the best quality product & service with all of our heart!
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Feature: | Corrosion-Resistant |
|---|---|
| Fare un passo: | Doppio passo |
| Openness: | Closed |
| Installazione: | Vertical |
| Transmission Form: | Verme |
| Tipo: | Single-Row Ball |
| Personalizzazione: | Disponibile | Richiesta personalizzata |
|---|
Maintenance Tips for Prolonging the Life of a Worm Gearbox
Proper maintenance is essential to ensure the longevity and reliable performance of a worm gearbox. Here are some maintenance tips to consider:
- Lubrificazione: Regularly check and replenish the lubricant in the gearbox. Use the recommended lubricant type and quantity specified by the manufacturer.
- Lubrication Schedule: Follow a lubrication schedule based on the operating conditions and manufacturer recommendations. Regular lubrication prevents friction, reduces wear, and dissipates heat.
- Temperature Monitoring: Keep an eye on the operating temperature of the gearbox. Excessive heat can degrade the lubricant and damage components.
- Cleanliness: Keep the gearbox and surrounding area clean from debris and contaminants. Regularly inspect and clean the gearbox exterior.
- Seal Inspection: Check for any leaks or damage to seals and gaskets. Replace them promptly to prevent lubricant leaks and contamination.
- Alignment: Ensure proper alignment between the worm and worm wheel. Misalignment can lead to increased wear and reduced efficiency.
- Torque Monitoring: Monitor the torque levels during operation. Excessive torque can cause overloading and premature wear.
- Regular Inspections: Periodically inspect all components for signs of wear, damage, or unusual noise. Replace worn or damaged parts promptly.
- Proper Usage: Operate the gearbox within its specified limits, including load, speed, and temperature. Avoid overloading or sudden changes in operating conditions.
- Expert Maintenance: If major maintenance or repairs are needed, consult the manufacturer’s guidelines or seek the assistance of qualified technicians.
By following these maintenance tips and adhering to the manufacturer’s recommendations, you can extend the lifespan of your worm gearbox and ensure its optimal performance over time.
Un riduttore a vite senza fine richiede una manutenzione frequente?
I riduttori a vite senza fine generalmente richiedono una manutenzione meno frequente rispetto ad altri tipi di riduttori, grazie alla loro progettazione e alle loro caratteristiche operative. Tuttavia, la manutenzione rimane essenziale per garantire prestazioni ottimali e una lunga durata. Ecco alcuni punti chiave da considerare:
- Lubrificazione: Una lubrificazione adeguata è fondamentale per i riduttori a vite senza fine. Controllare regolarmente il livello e la qualità del lubrificante per prevenire usura e surriscaldamento. Il lubrificante deve essere sostituito secondo le raccomandazioni del produttore.
- Ispezioni: Ispezionare periodicamente il cambio per individuare eventuali segni di usura, danni o perdite d'olio. Verificare la presenza di rumori insoliti, vibrazioni o cambiamenti nelle prestazioni che potrebbero indicare un problema.
- Serraggio e allineamento: Controllare e serrare eventuali elementi di fissaggio allentati e assicurarsi che il cambio sia correttamente allineato. Un disallineamento può causare un'usura maggiore e una riduzione dell'efficienza.
- Manutenzione delle guarnizioni: Ispezionare e manutenere le guarnizioni per evitare perdite d'olio e l'ingresso di contaminanti nel cambio.
- Pulizia: Mantieni il cambio pulito da detriti e contaminanti che potrebbero comprometterne le prestazioni. Una pulizia regolare può prevenire usura e danni prematuri.
- Carico e velocità: Assicurarsi che il cambio funzioni entro i limiti di carico e velocità nominali. Il superamento di tali limiti può causare un'usura accelerata e potenziali guasti.
- Condizioni ambientali: Consider the operating environment of the gearbox. Extreme temperatures, humidity, and other factors can impact the gearbox’s performance and longevity.
While worm gearboxes are known for their durability and self-locking feature, neglecting maintenance can lead to premature wear, reduced efficiency, and potential breakdowns. Following the manufacturer’s recommendations for maintenance intervals and procedures is essential to keep the worm reducer in optimal condition.
Lubrication Requirements for a Worm Gearbox
Lubrication is crucial for maintaining the performance and longevity of a worm gearbox. Here are the key considerations for lubricating a worm gearbox:
- Type of Lubricant: Use a high-quality, high-viscosity lubricant specifically designed for worm gearboxes. Worm gearboxes require lubricants with additives that provide proper lubrication and prevent wear.
- Lubrication Interval: Follow the manufacturer’s recommendations for lubrication intervals. Regularly check the gearbox’s temperature and oil condition to determine the optimal frequency of lubrication.
- Oil Level: Maintain the proper oil level to ensure effective lubrication. Too little oil can lead to insufficient lubrication, while too much oil can cause overheating and foaming.
- Lubrication Points: Identify all the lubrication points on the gearbox, including the worm and wheel gear surfaces. Apply the lubricant evenly to ensure complete coverage.
- Temperature: Consider the operating temperature of the gearbox. Some lubricants have temperature limits, and extreme temperatures can affect lubricant viscosity and performance.
- Cleanliness: Keep the gearbox and the surrounding area clean to prevent contaminants from entering the lubricant. Use proper filtration and seals to maintain a clean environment.
- Monitoring: Regularly monitor the gearbox’s temperature, noise level, and vibration to detect any signs of inadequate lubrication or other issues.
Proper lubrication will reduce friction, wear, and heat generation, ensuring smooth and efficient operation of the worm gearbox. Always refer to the manufacturer’s guidelines for lubrication specifications and intervals.
editor by CX 2024-03-09