Өнім сипаттамасы
Coresun Drive slewing drive gear motor worm drive for horizontal single-axis solar tracking system. For horizontal single-axis solar tracking system, the main shaft of solar panel will adjust the angle to precisely track the declination angle. This kind of slewing drive is only applied for low latitudes area.
Slew Drive is a new type of slewing product, usually called slewing ring, which is usually composed of worm, slewing ring, housing, motor and other components. Since the core components are slewing bearings, they can simultaneously withstand axial forces, radial forces, and overturning moments. Compared with traditional rotary products, the new slewing drive features easy installation, easy maintenance and a greater degree of installation space.
Slew Drive are widely used in PV,CPV,STP solar tracking systems and construction applications including truck cranes, manlifts, turntables, port machinery, modular vehicles, small wind power systems and satellite communications.
Glossary
Tilting Moment Torque: Torque is the load multiplied by distance between the position of load and the center of slewing bearing. If the qorque generated by load and distance is greater than the rated tilting moment torque, slewing drive will be overturned.
Radial load: Load vertical to the axis of slewing bearing
Axial load: Load parallel to the axis of slewing bearing
Holding torque:It is the reverse torque.When the drive is rotating reversely, and parts are not damaged,The maximum torque achieved is called holding torque.
Self-locking: Only when loaded, the slewing drive is not able to reverse rotate and thus called self-loc
| Модель | VH9 | Place of Origin | HangZhou,China |
| Brand | Coresun Drive | Түрі | Vertical |
| Материал | 42CrMo,50Mn | Output Torque | 6405N.m |
| Tilting Moment Torque | 12KN.m | Holding Torque | 56KN.m |
| Static Axial Rating | 350KN | Static Radial Rating | 120KN |
| Dynamic Axial Rating | 168KN | Dynamic Radial Rating | 65KN |
| Gear Ratio | 61:1 | Тиімділік | 40% |
Біз туралы
CHINAMFG – Practical Slewing Drive & Slewing Bearing Promoter.
We are committed to researching, developing and applying high quality, precision transmission equipment products,who provides reliable mechanical actuator for horizonal single axis, dual-axis photovoltaic tracking system, CSP,CPV solar tracking design.Our professional and high-quality products will be also applied well as a steady solution on aerial working platform, truck crane, timber grab, drilling rig, spray equipment, hydraulic module vehicle,automated assembly lines, wind yaw systems,etc.
1. Our company’s worm gear reducer (slewing drive device) adopts the transmission mode of plane secondary enveloping ring surface worm combined with slewing support, which can realize multi-tooth meshing.
2. On the premise of not affecting the performance of the whole device, we improved and optimized it, and its overall thickness became thinner and weight became lighter.
3. The rotary device at the center is a through hole for the customer to use. The original product is solid.
4. The worm material is 42CrMo, the secondary nitride treatment, the slewing bearing material is 50Mn, the teeth are quenched, and its wear resistance is good.
Why choose us
1. We are a manufacturer of producing slewing drive and bearing for more than 10 years.
2. We have advanced mechanical equipment and strict quality control team.
3. Efficient production speed and on-time delivery service.
4. Accept standard and non-standard production.
Products Photo
Application
Photovoltaic power generation is an important application field of rotary drive, using slewing drive VH9 as a rotating component of solar photovoltaic modules, according to the position of the sun in a day to the host of the angle and elevation of accurate adjustment, time is the solar panel for better reception angle, can make greater efficiency of power generation.
Horizontal Single Axis PV solar tracker system. The slewing drive VH9 is available for 60-150 square meter solar tracker design.
Products Certificate
Coresun Drive slewing drive gear motor have arroved by CE and ISO2001 certificate.
CONTACT US
It is sincerely looking CHINAMFG to cooperating with you for and providing you the best quality product & service with all of our heart!
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Feature: | Corrosion-Resistant |
|---|---|
| Қадам: | Double-Step |
| Openness: | Closed |
| Орнату: | Vertical |
| Transmission Form: | Құрт |
| Түрі: | Single-Row Ball |
| Теңшеу: | Қолжетімді | Теңшелген сұраныс |
|---|
Maintenance Tips for Prolonging the Life of a Worm Gearbox
Proper maintenance is essential to ensure the longevity and reliable performance of a worm gearbox. Here are some maintenance tips to consider:
- Майлау: Regularly check and replenish the lubricant in the gearbox. Use the recommended lubricant type and quantity specified by the manufacturer.
- Lubrication Schedule: Follow a lubrication schedule based on the operating conditions and manufacturer recommendations. Regular lubrication prevents friction, reduces wear, and dissipates heat.
- Temperature Monitoring: Keep an eye on the operating temperature of the gearbox. Excessive heat can degrade the lubricant and damage components.
- Тазалық: Keep the gearbox and surrounding area clean from debris and contaminants. Regularly inspect and clean the gearbox exterior.
- Seal Inspection: Check for any leaks or damage to seals and gaskets. Replace them promptly to prevent lubricant leaks and contamination.
- Alignment: Ensure proper alignment between the worm and worm wheel. Misalignment can lead to increased wear and reduced efficiency.
- Torque Monitoring: Monitor the torque levels during operation. Excessive torque can cause overloading and premature wear.
- Regular Inspections: Periodically inspect all components for signs of wear, damage, or unusual noise. Replace worn or damaged parts promptly.
- Proper Usage: Operate the gearbox within its specified limits, including load, speed, and temperature. Avoid overloading or sudden changes in operating conditions.
- Expert Maintenance: If major maintenance or repairs are needed, consult the manufacturer’s guidelines or seek the assistance of qualified technicians.
By following these maintenance tips and adhering to the manufacturer’s recommendations, you can extend the lifespan of your worm gearbox and ensure its optimal performance over time.
Does a Worm Reducer Require Frequent Maintenance?
Worm reducers generally require less frequent maintenance compared to some other types of gearboxes due to their design and operating characteristics. However, maintenance is still essential to ensure optimal performance and longevity. Here are some key points to consider:
- Майлау: Proper lubrication is crucial for worm gearboxes. Regularly check the lubricant level and quality to prevent wear and overheating. Lubricant should be changed as recommended by the manufacturer.
- Inspections: Periodically inspect the gearbox for signs of wear, damage, or oil leaks. Check for any unusual noises, vibrations, or changes in performance that could indicate a problem.
- Tightening and Alignment: Check and tighten any loose fasteners and ensure that the gearbox is properly aligned. Misalignment can lead to increased wear and reduced efficiency.
- Seal Maintenance: Inspect and maintain seals to prevent oil leakage and contaminants from entering the gearbox.
- Cleaning: Keep the gearbox clean from debris and contaminants that could affect its performance. Regular cleaning can prevent premature wear and damage.
- Load and Speed: Ensure that the gearbox is operating within its rated load and speed limits. Exceeding these limits can lead to accelerated wear and potential failure.
- Environmental Conditions: Consider the operating environment of the gearbox. Extreme temperatures, humidity, and other factors can impact the gearbox’s performance and longevity.
While worm gearboxes are known for their durability and self-locking feature, neglecting maintenance can lead to premature wear, reduced efficiency, and potential breakdowns. Following the manufacturer’s recommendations for maintenance intervals and procedures is essential to keep the worm reducer in optimal condition.
Құрт тәрізді беріліс қорабын майлау талаптары
Майлау червяк беріліс қорабының өнімділігі мен ұзақ қызмет ету мерзімін сақтау үшін өте маңызды. Червяк беріліс қорабын майлаудың негізгі аспектілері:
- Майлағыш түрі: Құрт тәрізді беріліс қораптарына арнайы жасалған жоғары сапалы, жоғары тұтқырлықты майлағышты пайдаланыңыз. Құрт тәрізді беріліс қораптары тиісті майлауды қамтамасыз ететін және тозуды болдырмайтын қоспалары бар майлағыштарды қажет етеді.
- Майлау аралығы: Follow the manufacturer’s recommendations for lubrication intervals. Regularly check the gearbox’s temperature and oil condition to determine the optimal frequency of lubrication.
- Май деңгейі: Тиімді майлауды қамтамасыз ету үшін майдың тиісті деңгейін сақтаңыз. Майдың тым аз болуы жеткіліксіз майлауға әкелуі мүмкін, ал майдың тым көп болуы қызып кетуге және көбіктенуге әкелуі мүмкін.
- Майлау нүктелері: Беріліс қорабындағы барлық майлау нүктелерін, соның ішінде құрт тәрізді және доңғалақ берілістерінің беттерін анықтаңыз. Толық жабуды қамтамасыз ету үшін майлағышты біркелкі жағыңыз.
- Температура: Беріліс қорабының жұмыс температурасын ескеріңіз. Кейбір майлағыштардың температуралық шектеулері бар, ал шамадан тыс температуралар майлағыштың тұтқырлығы мен өнімділігіне әсер етуі мүмкін.
- Тазалық: Майлағышқа ластаушы заттардың түсуіне жол бермеу үшін беріліс қорабын және оның айналасын таза ұстаңыз. Таза қоршаған ортаны сақтау үшін тиісті сүзгілер мен тығыздағыштарды пайдаланыңыз.
- Бақылау: Regularly monitor the gearbox’s temperature, noise level, and vibration to detect any signs of inadequate lubrication or other issues.
Proper lubrication will reduce friction, wear, and heat generation, ensuring smooth and efficient operation of the worm gearbox. Always refer to the manufacturer’s guidelines for lubrication specifications and intervals.
editor by CX 2024-03-09