WPEX Double Speed Cast Iron Worm Reducer — WP Series

The WPEX is the double-stage counterpart to the single-stage WPX: X-type vertical downward output for ceiling and inverted installations, extended to ratios 1/200–1/900+ by the dual worm stage architecture. Overhead mining conveyor drives running below 5 rpm, sub-floor mechanism drives, and ceiling-mounted gravity-assist systems requiring extreme ratios use WPEX where no single-stage overhead reducer can deliver the required output speed.

✉ कीमत का अनुरोध करें | एवर पावर के बारे में

■ X-Type Downward Output + Double Stage — Extreme Ratio Ceiling Drive

The WPEX combines X-type vertical downward output with two-stage extreme ratio reduction — providing ratios 1/200 to 1/900+ in a ceiling-mount or inverted installation. Applications requiring output speeds below 10 rpm from an overhead drive unit use WPEX where a single-stage WPX would only reach 1/60.

■ Same 6,050 Nm Output Torque as WPEA

X-type output does not affect dual-stage torque capacity. WPEX size 155–250 delivers 6,050 Nm.

■ Oil Circuit for X-Type Inverted/Downward Orientation

Both chamber oil volumes are adjusted for X-type inverted orientation. Use the WPEX lubrication table for correct volumes in ceiling/inverted mounting.

■ Bilateral Horizontal Input — Motor from Either Side

Horizontal bilateral input shaft retained in X-type configuration — motor connects from either side of the ceiling-mounted housing.

■ FC20+ Dual-Chamber Cast Iron — Inverted Load Stability

Cast iron housing maintains dimensional stability under the sustained inverted load of ceiling-mount installation. Dual-chamber design maintains inter-stage alignment at operating temperature.

■ Independent Oil Chambers — Both Stages

Two independent sealed chambers with separate fill, gauge, and drain — each maintained independently on 2,500-hour intervals.

⚊ Overhead Mining Conveyor Slow Drives

WPEX ceiling-mount with X-type downward output drives mining conveyor head shafts at ultra-slow speeds (below 5 rpm) directly from a standard motor — eliminating the VFD that single-stage ceiling drives require for comparable speeds.

⚒ Sub-Floor Mechanism Drives

Extreme-ratio ceiling-mounted drives for sub-floor conveyor mechanisms and under-floor turntable drives use WPEX downward output shaft to reach the driven equipment below the mounting structure.

☵ Ceiling-Mounted Gravity-Feed Controls

Overhead X-type slow drive for gravity-feed gate and hopper control mechanisms requiring ultra-slow, high-torque operation from a compact ceiling-mount unit.

⚛ Overhead Process Line Positioning

Industrial positioning systems requiring ceiling-mount drive units at extreme ratios for indexing, scanning, and inspection system overhead drives use WPEX for the combination of inverted mounting and extreme ratio.

■ आईएसओ 9001:2000 — दो-चरणीय असेंबली प्रमाणित

दोनों वर्म स्टेज असेंबली का निर्माण और परीक्षण ISO 9001:2000 के तहत किया जाता है। प्रत्येक यूनिट की अंतिम असेंबली से पहले इंटर-स्टेज अलाइनमेंट और अनुपात सटीकता की पुष्टि की जाती है।

■ सीई मार्किंग — यूरोपीय संघ मशीनरी निर्देश 2006/42/ईसी

यूरोपीय संघ, ब्रिटेन, ऑस्ट्रेलिया और न्यूजीलैंड के बाजारों में निर्यात के लिए पूर्ण सीई अनुपालन, पुन: प्रमाणन की आवश्यकता नहीं है।

■ शिपमेंट से पहले परीक्षण: शोर, रिसाव, टॉर्क

निर्धारित भार पर शोर का स्तर 68 dB(A) से कम, दोनों गियर कक्षों का 30 मिनट तक दबावयुक्त रहना, और आउटपुट टॉर्क निर्धारित मान के ±5% के भीतर होना चाहिए। दोषपूर्ण इकाइयों को शिपमेंट से पहले संशोधित किया जाएगा।

■ FC20+ सामग्री प्रमाणन

दोनों हाउसिंग में FC20 मिलिंग प्रमाणपत्र हैं: न्यूनतम तन्यता शक्ति 220 MPa, कठोरता 160–200 HB। 135–200 और उससे ऊपर के आकार संयोजनों पर अल्ट्रासोनिक परीक्षण किया गया है।

“WPEX ceiling-mounted on our mining conveyor overhead drives. X-type downward output shaft connects directly to the conveyor head shaft below. 1/600 ratio from a standard motor — no VFD needed.”

“Used WPEX on sub-floor conveyor mechanism drives. Double-stage at 1/500 with downward output shaft through the floor structure. Clean installation with no external coupling below the mounting frame.”

“WPEX on our ceiling-mounted gravity feed gate drives. 1/800 ratio, 2,100 Nm output, vertical downward shaft to the gate mechanism. Reliable slow-speed control from a compact overhead unit.”

“Good double-stage inverted drive. WPEX-80–135 on our overhead process line indexing drives. Extreme ratio, vertical downward output, correct torque. Would appreciate D-split maintenance access variant.”